DisplayPort 1.4 vs 2.1: Do You Need the Upgrade?

Specs
Table of contents

DisplayPort 2.1 has about three times the bandwidth of DisplayPort 1.4. DP 1.4 tops out at 32.4 Gbps, while DP 2.1 adds new link rates of 40, 54 and 80 Gbps. That sounds like a must-have, but DP 1.4 already drives 4K at 240Hz by using DSC compression. You only need DisplayPort 2.1 if you want those modes without compression, 4K above 240Hz, 8K at high refresh, or several fast monitors on a single cable.

DP 1.4 vs 2.1 at a glance

The core difference is how fast each lane runs and how much of that speed is lost to encoding. Both versions send data over four lanes inside the same cable.

DisplayPort 1.4 vs 2.1: link rates and usable bandwidth
Link ratePer laneRaw total (4 lanes)Usable dataEncoding
HBR3 (DP 1.4)8.1 Gbps32.4 Gbps25.92 Gbps8b/10b
UHBR10 (DP 2.1)10 Gbps40 GbpsAbout 38.7 Gbps128b/132b
UHBR13.5 (DP 2.1)13.5 Gbps54 GbpsAbout 52.2 Gbps128b/132b
UHBR20 (DP 2.1)20 Gbps80 Gbps77.37 Gbps128b/132b

The HBR3 and UHBR20 figures come straight from VESA, the group that writes the DisplayPort standard. The UHBR10 and UHBR13.5 data figures are the same ratio applied to their lower link rates, so treat them as close estimates.

Why the encoding matters

Encoding is the extra bits a link adds so the receiver can stay in sync and catch errors. DP 1.4 uses 8b/10b, which sends 10 bits for every 8 bits of picture. That throws away 20 percent of the link before any image data moves, which is why 32.4 Gbps shrinks to 25.92 Gbps.

DP 2.1 uses 128b/132b, which sends 132 bits for every 128. The overhead drops to about 3 percent. So DP 2.1 gains twice: the lanes run faster, and less of each lane is wasted.

What DSC does on DisplayPort

DSC (Display Stream Compression) is a VESA compression method that shrinks the video signal on its way down the cable. The monitor unpacks it before showing the image. VESA designs DSC to be visually lossless, and in its DP 2.1 announcement says DSC can cut the bandwidth a signal needs by more than 67 percent without visible artifacts.

DisplayPort 1.4 was the first DisplayPort version to use DSC, and DP 2.1 makes it mandatory. This is the reason the 1.4 vs 2.1 gap is smaller in practice than the raw numbers suggest.

Take a 4K 240Hz monitor in 10-bit color. The pixels alone add up to about 60 Gbps before any timing overhead. That is more than double what DP 1.4 can carry, yet it works, because DSC squeezes it down. Our MSI MAG 321URX settings guide shows this on a real monitor: it needs DSC switched on to offer 4K 240Hz at 10-bit over DisplayPort 1.4. Our guide to 8-bit vs 10-bit monitors covers when that extra depth is worth it.

DSC is still compression, and it needs support on both the graphics card and the monitor. Many monitors let you switch it off in their menu, which also removes the modes that depend on it. If 240Hz or 10-bit disappears after a menu change, check that DSC is still on.

What each version can drive

Each version’s limits depend on whether DSC is in the chain. The examples below come from VESA, NVIDIA and AMD, not from guesswork.

Diagram comparing 1080p, 1440p and 4K pixel grids side by side
Each step up in resolution multiplies the pixels a link has to carry every frame, which is where DP 2.1's extra bandwidth goes.

DisplayPort 1.4

Without compression, DP 1.4 reaches about 4K at 120Hz in 8-bit color. With DSC, VESA lists 8K at 60Hz HDR and 4K at 120Hz HDR as headline modes, and graphics card makers go further. NVIDIA rates the DP 1.4a outputs on its RTX 40 cards for up to 4K 12-bit HDR at 240Hz or 8K at 60Hz, both with DSC.

That covers almost every monitor on sale, from 1440p at 360Hz to 4K at 240Hz. If you are still deciding how much refresh rate you need, our guide to whether 165Hz is good for gaming is a good place to start.

DisplayPort 2.1

VESA lists uncompressed 8K at 60Hz HDR and 4K at 240Hz HDR among the use cases UHBR makes possible. Without DSC, its examples also include two 4K displays at 144Hz in 8-bit color, or three 4K displays at 90Hz in 10-bit HDR, from one port. With DSC, VESA’s examples reach a single 16K (15360x8640) display at 60Hz.

For UHBR13.5 specifically, VESA says four lanes can drive 8K by 2K (7680x2160) at 240Hz or full 8K at 120Hz. Those modes are far beyond 54 Gbps of raw pixel data, so they also lean on DSC.

On the GPU side, NVIDIA rates its RTX 50 cards, using DP 2.1b with UHBR20 and DSC, for up to 4K 12-bit HDR at 480Hz or 8K 12-bit HDR at 165Hz.

Example modes by version, as listed by VESA or the GPU maker
ModeDisplayPort 1.4DisplayPort 2.1 (UHBR20)
4K 120HzYes, 8-bit without DSCYes, without DSC
4K 240Hz 10-bitYes, with DSCYes, without DSC
4K 480HzNoYes, with DSC (NVIDIA RTX 50)
8K 60Hz HDRYes, with DSCYes, without DSC
8K 165HzNoYes, with DSC (NVIDIA RTX 50)

DP 2.1 cables: DP40, DP54 and DP80

A DP 2.1 port only reaches UHBR speeds if the cable can carry them. VESA certifies UHBR cables by the bandwidth they handle, and the name on the cable or box tells you the ceiling.

VESA certified DisplayPort cable tiers
CableTop link rateMax bandwidthLength
DP8KHBR3 (DP 1.4)32.4 GbpsVaries by product
DP40 (now rated DP54)UHBR10, retested to UHBR13.540 Gbps, now 54 GbpsOver 2 m
DP54UHBR13.554 GbpsUp to 2 m passive
DP80UHBR2080 GbpsAbout 1 m passive
DP80LLUHBR2080 GbpsUp to 3 m active

The DP54 tier came with DisplayPort 2.1a. In its DP54 announcement from January 2024, VESA says DP54 replaces DP40, carries four-lane UHBR13.5 over a two meter passive cable, and that DP40 cables already shipped passed testing at the DP54 level. Before that, UHBR13.5 needed a one meter DP80 cable.

DisplayPort 2.1b added DP80LL, an active “low loss” cable that carries full UHBR20 up to three meters. Active cables contain small chips that boost the signal, so they cost more, but they remove the one meter limit that makes passive DP80 awkward on a big desk.

Picking a dp 2.1 cable

Match the cable to the slower end of your setup. If your graphics card and monitor both support UHBR20 and you want every bit of bandwidth, buy a VESA certified DP80 (1 meter) or DP80LL (longer runs). If either end tops out at UHBR13.5, a certified DP54 cable is enough and can be twice as long.

Look for the VESA certification logo and the tier name on the packaging. An uncertified cable labeled “8K” or “DP 2.1” may work at HBR3 and fail at UHBR speeds, which shows up as flicker, black screens or a lower refresh rate than you picked. Our guide on how to connect a monitor covers the basics of choosing the right port and cable.

Which graphics cards support DisplayPort 2.1?

The version number alone does not tell you the speed. A port can be fully DP 2.1 and still top out at UHBR10 or UHBR13.5, so check the UHBR level on the maker’s spec page.

  • NVIDIA RTX 50 series: NVIDIA’s RTX 5090 specs list DisplayPort 2.1b with UHBR20, and the RTX 5070 Ti and 5070 pages list the same. This is the full 80 Gbps tier.
  • NVIDIA RTX 40 series and older: DisplayPort 1.4a. NVIDIA’s RTX 4090 page, for example, lists DP 1.4a with up to 4K 240Hz or 8K 60Hz using DSC.
  • AMD Radeon RX 7000 series: AMD launched the RX 7900 XTX and 7900 XT with DisplayPort 2.1 at UHBR13.5, up to 54 Gbps. Other RX 7000 cards can differ, so check each model.
  • AMD Radeon RX 9000 series: AMD lists DisplayPort 2.1a and HDMI 2.1b for the RX 9070 XT. Its spec pages do not state the UHBR level, so check your exact card or board partner’s specs before buying a UHBR20 monitor for it.

Make sure the monitor is plugged into the graphics card, not the motherboard. Motherboard ports run off the processor’s graphics and usually support a lower DisplayPort version, if they give a picture at all.

Diagram of a PC back panel showing motherboard ports and graphics card ports
Plug the monitor into the graphics card's DisplayPort output. The motherboard ports may not support DP 2.1 or may show nothing.

Backward compatibility, MST and USB-C

DisplayPort 2.1 is fully backward compatible. VESA confirms that DP 2.x works with earlier versions, and the connector has not changed. A DP 2.1 monitor works on a DP 1.4 graphics card, and a DP 1.4 monitor works on a DP 2.1 card. The link simply runs at the fastest rate that the card, the cable and the monitor all support.

Multi-stream (MST)

Both versions support MST, where one DisplayPort output drives several monitors through a hub or by daisy-chaining. The monitors share the link’s bandwidth, so DP 2.1’s extra headroom lets one port feed more or faster screens. If you plan to run several displays, our triple monitor graphics card guide explains how outputs and MST hubs fit together.

Diagram of a PC connected to several monitors in a DisplayPort MST daisy chain
With MST, one DisplayPort output feeds a chain of monitors that all share the same link bandwidth.

USB-C DisplayPort Alt Mode

DisplayPort also runs over USB-C through DisplayPort Alt Mode, and DP 2.1 is built to line up with USB4, so the same port can carry both. Not every USB-C port carries video, though. The laptop or phone has to support Alt Mode, and the UHBR speed it reaches depends on the device. Our guide to connecting a phone to a monitor covers how to check whether a USB-C port outputs video.

Diagram of one USB-C port showing charging, data and video paths
A USB-C port can carry charging, data and video, but only outputs DisplayPort if it supports Alt Mode.

Do you need DisplayPort 2.1?

Most people do not, at least not yet. DisplayPort 1.4 with DSC drives every common gaming setup up to 4K 240Hz, and works well with features like adaptive sync.

DisplayPort 2.1 makes sense if:

  • You own a 4K monitor above 240Hz. NVIDIA’s 4K 480Hz rating, for example, depends on DP 2.1b with UHBR20 plus DSC.
  • You want 4K 240Hz in 10-bit without any compression.
  • You run 8K, or 5K and 6K screens at high refresh.
  • You drive several fast monitors from one port through MST or a dock.
  • You are buying a new monitor and GPU together. Matching UHBR20 on both ends future-proofs the pair, as long as you also buy a DP80 cable.

You can skip it if you game at 1440p or at 4K up to 240Hz, if your graphics card is an RTX 40 or older, or if your monitor’s spec sheet only lists DP 1.4. In that last case, a DP 2.1 card adds nothing to that screen. Resolution still sets most of the load, so our 4K vs 1080p comparison is worth a look if you are deciding how far to push it.

If you do set up a UHBR link, confirm it took. Open Settings > System > Display > Advanced display in Windows and check that the refresh rate matches what you picked. If the higher modes are missing, the usual causes are an uncertified cable, a monitor port set to an older DP version in its menu, or a GPU that tops out at a lower UHBR level. HDR modes add to the bandwidth too, which matters on high refresh OLED monitors running HDR.

Conclusion

DisplayPort 1.4 vs 2.1 comes down to whether DSC is enough for you. DP 1.4 carries about 25.9 Gbps of data and reaches 4K 240Hz and 8K 60Hz with DSC, which covers most monitors today. DP 2.1 adds UHBR10, UHBR13.5 and UHBR20, up to 77.37 Gbps, for 4K above 240Hz, 8K at high refresh and uncompressed 4K 240Hz. If you upgrade, match the UHBR level on the GPU and monitor and buy a certified DP54 or DP80 cable. For more on ports, panels and specs, browse our specs guides or the full SubInsider monitor knowledge base.

Frequently asked questions

Do I need DisplayPort 2.1 for 4K 144Hz?

No. DisplayPort 1.4 runs 4K at 144Hz, using DSC compression for 10-bit color, and almost every 4K 144Hz monitor is built around that. DisplayPort 2.1 only starts to matter when you want 4K at 240Hz without compression, 4K above 240Hz, or 8K at a high refresh rate.

Can I use a DisplayPort 1.4 cable on a DisplayPort 2.1 port?

Yes. The connector is the same and the versions are backward compatible, so the picture will work. A DP 1.4 class cable is only tested for HBR3 speeds, though, so the link may fall back to 32.4 Gbps or drop out at UHBR rates. For UHBR13.5 or UHBR20, use a VESA certified DP54 or DP80 cable.

Does DSC reduce image quality?

VESA designs DSC to be visually lossless, meaning you should not see artifacts in normal use, and it can cut the bandwidth a signal needs by more than 67 percent. It is a standard part of DisplayPort 1.4 and is mandatory in DisplayPort 2.1, so both ends of most high refresh setups already support it.

Is DisplayPort 2.1 the same as UHBR20?

No. DisplayPort 2.1 is the version of the standard, and UHBR20 is its fastest link rate. A port labeled DP 2.1 may top out at UHBR10 or UHBR13.5 instead. NVIDIA lists UHBR20 for RTX 50 cards, while AMD lists UHBR13.5 for the RX 7900 series, so check the UHBR level, not just the version number.

What is the difference between DP 2.1a and DP 2.1b?

Both are updates to DisplayPort 2.1 that mostly change cables. DP 2.1a replaced the DP40 cable spec with DP54, which carries UHBR13.5 over a 2 meter passive cable. DP 2.1b added DP80LL, an active cable that carries UHBR20 up to 3 meters. Devices from all three versions work together.